Updated May 21, 2019 10:42:06 New York Jets quarterback Bryce Petty is back to work after being sidelined for the past three games with a neck injury.New York coach Todd Bowles said Tuesday that the former Heisman Trophy winner has a "pretty good chance" to play against the Denver Broncos on Sunday, and he expects him to play Sunday against Cincinnati.It's the first time Petty has played in consec...
I’ve been building a new building for myself for the past few months, and I thought it might be fun to show you how to do it.
I know, it’s pretty simple: use the instructions on the internet, make a bunch of drawings, and then put them all together.
But what’s interesting about this build is that it’s not actually all that hard.
Here’s the basic building concept, with a few details I picked up from the internet: 1.
Get a piece of plywood that will fit the space in which you’re building the building.
You’ll want a piece that will sit on the floor (you want a floor that won’t be slippery, as you’ll be building the flooring on), and a piece for the roof.
There are plenty of ways to build your own roof.
I ended up building one with two layers of ply, but you could easily make one with just one or two layers.
Cut out the pieces.
You need to cut out the first piece so that you have a flat, straight edge, and two horizontal slices, each about the size of a quarter.
Then cut them out with a router, then cut a square out of them.
That will make the piece the first slice.
(The second slice is to make the roof) 3.
Cut the pieces out with your router.
Make sure the pieces are parallel to each other, and you have enough room between them.
If you’re doing the project on a wood-framed building, use a straight piece of wood as a template for the edges.
Drill a hole in the roof (if it’s on a steel frame).
This hole should be about half an inch deep.
The roof should be at least 2 feet in diameter.
(If it’s a wood frame, make the hole as big as you can make it with a pair of scissors.)
Screw on the roof piece.
(It’ll be the roof.)
Connect the roof pieces to the pieces of ply you just cut.
You should have a square of the same size as the two horizontal pieces.
(For the roof, use one horizontal slice, one vertical slice, and one round of the opposite thickness.)
Put the roof together, and it should be pretty easy to attach it to the wall.
The easiest way to put it together is to glue the two pieces together with epoxy, but that requires a lot of sandpaper.
You can glue it, or you can spray epoxy onto it and spray it down.
Either way, the roof should look like this: 8.
Then assemble the rest of the building, and the whole thing should look a lot more like this.
Put a bunch more plywood on the top of the roof and glue it all together, like this (or the picture below if you prefer the picture to have a few extra points of epoxy on the side.): 10.
The whole thing looks a lot better, except for one problem: the roof is going to be pretty big.
If it’s going to fit on the wall, you’re going to need to add a bunch and a half more feet, or more than an extra foot of height.
If the roof isn’t going to sit flush with the wall it’ll be a little too high.
So you’re looking at either cutting out the whole roof, or using a lot extra plywood.
You could just cut it out, but I think the extra layer of ply would look nicer, and also it’s easier to glue together.
Now that you’ve got the roof assembled, it is time to put the walls together.
You might have heard of the idea of “wall framing” before.
Wall framing is basically a way to build up the wall into a wall, so that it looks like the wall you’re framing will be there.
You basically use some kind of framing like a metal fence, and put a few pieces of lumber between them (this is where the roof comes in).
You then put some glue between them and put the roof on top of it.
You add some epoxy to the glue, and when the glue dries, you can put the extra ply over the glue and put it in place.
You don’t have to put a roof on the inside of the walls to do this, but if you want to you can.
Now all that’s left to do is put the interior walls together!
The walls will look a little different, but it should still look pretty good.
Now we’re going back to the drawing board, and we can start to make a few more changes to make sure that everything looks good.
First, make sure your planks are level.
You want them to sit on one another, but not perfectly level.
(I used a 1-1/4″ thick plywood board that had been cut from a 1/2″ thick sheet of ply.)